Reproductions of discontinued exhaust hangers

ZMan38 said:
Hello, are you still reproducing parts? The last picture you have there is the one I can't find anywhere (Jeep YJ part 52002743), which holds the catalytic converter in place. I have pics of my old part if that helps. Thanks-Mark
Click to expand...
What is left of your old part? If the lower section is still good, I can weld on a new upper section. I can make a new one that should fit, but repairing the old one is easier. You're not too far from me in NJ, so I'm sure we can get together and get you a part that will work.
 
20221201_223955.jpg

dsaul said:
What is left of your old part? If the lower section is still good, I can weld on a new upper section. I can make a new one that should fit, but repairing the old one is easier. You're not too far from me in NJ, so I'm sure we can get together and get you a part that will work.
Click to expand...
That would be great. Welding on a new top would do it. The base is still good, it's the top part that they welded to the exhaust pipe which is no longer usable.
 
dsaul said:
What is left of your old part? If the lower section is still good, I can weld on a new upper section. I can make a new one that should fit, but repairing the old one is easier. You're not too far from me in NJ, so I'm sure we can get together and get you a part that will work.
Click to expand...
I can run the part up to you depending your availability, looks like I'm about 30 min. away
 
  • Like
Reactions: dsaul
Ethankubala said:
Any luck on reproducing part number 52003925? Transmission mount bracket.
Click to expand...
I could easily reproduce the metal part, if I had one to get measurements from. The hard part is sourcing the rubber piece. They do not appear to be a replaceable part, so they aren't available aftermarket.

There are a few of these parts for sale on ebay, although they are not listed by part number. I think these are the correct part. https://www.ebay.com/itm/4040654742...d=link&campid=5337789113&toolid=20001&mkevt=1

www.ebay.com

Jeep Wrangler YJ 2.5L AX5 Manual Transmission Mount Exhaust Bracket 87-95 e | eBay

Used Jeep Wrangler YJ 2.5L 4 cylinder AX5 manual transmission mount bracket. This bracket bolts to the transmission and the rubber mount bolts to this. This will fit YJ model years 1987-1995 with the AX5 transmission.
www.ebay.com
 
This site contains affiliate links for which Jeep Wrangler YJ Forum may be compensated.
This site contains affiliate links for which Jeep Wrangler YJ Forum may be compensated.
Still possible to get one of those tailpipe hanger (complete)? Please respond at jorn_olsen76at)hotmail com.
 
I have finalized the design on the reproduction of the Catalytic converter hanger part # 52002743. I have a couple of them made and will probably sell them for $45 + shipping. Message me or email me at ds690@comcast.net, if you are interested.
PXL_20230816_181053788.jpg
PXL_20230816_181112978.jpg
 
  • Like
Reactions: machoheadgames
dsaul said:
I have finalized the design on the reproduction of the Catalytic converter hanger part # 52002743. I have a couple of them made and will probably sell them for $45 + shipping. Message me or email me at ds690@comcast.net, if you are interested. View attachment 121690View attachment 121691
Click to expand...
Once again, nice work! If I had the older cat that used this bracket, I'd be all over one. I wish the transmission brackets were easier to produce and that a good rubber isolator bushing was available to use with the U slot in it for the cat support.
 
  • Like
Reactions: dsaul
dsaul said:
I don't own a Jeep, but a friend of mine owns a YJ and asked me if I could reproduce the tailpipe hanger clamp(Mopar part # 52003427) for him. I had a hard time even finding a picture of one, but I was able to make one using the Mopar parts drawing and the other half of the hanger that he was able to purchase (Mopar part # 52003426). I made a few extras to sell on eBay to anyone else who needed the part and it turned out that a lot of people need them.
View attachment 118792

A few months later, I got a request for the other half of the hanger and found that they were no longer available for sale anywhere. I was able to produce a similar part, but with relief cuts for bending, since I don't have a huge press in my garage. Pictured below is the full assembly that I produce. View attachment 118793

I have a couple of parts in the prototype/testing phase that I'm waiting for some feedback on. Those being the muffler hanger and the hanger that attched to the catalytic converter. Both have been modified to fit the capabilities that I have in my small garage workshop. View attachment 118794View attachment 118795

I am open to trying to reproduce other parts as well, as long as they are not too large or complex for me to be able to do in my shop. Please send me a private message with any requests.

I will probably be listing the tailpipe hanger parts in the for sale section and any other parts after they are tested.
Click to expand...
Are the hangers for sale anywhere?
Looking for the one that bolts to the catalytic converter for an 89 yj 4 cyl
 
Top Bottom