Forums
New posts
Search forums
Image search
Shop
Amazon Store
T-Shirts
Stickers
Members
Current visitors
Supporting Member Upgrade
Sponsors
About
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Current visitors
Supporting Member Upgrade
Search
Search titles only
By:
Search titles only
By:
Menu
Install the app
Install
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Flyer58's latest activity
Flyer58
replied to the thread
Need Help Reinstalling Rear Driveshaft
.
When removing the U-joint did any of the cups fall off and possibly lose some of the roller needle bearings? It's also easy for then to...
Mar 18, 2024
Flyer58
reacted to
dodgerammit's post
in the thread
Help with windshield frame hinges
with
Like
.
I had a similar issue on a repop half door I purchased. The door sat WAY too far forward. Like, rubbing the tub at the hinges forward...
Mar 17, 2024
Flyer58
reacted to
machoheadgames's post
in the thread
1994 Hunter Green SE “Back to Stock” Thread
with
Like
.
Been busy lately. Finally cleaned up the garage, which helps a lot. Through parts of December and January and a bit of February, I got...
Mar 16, 2024
Flyer58
replied to the thread
Is there anything wrong with this fuel injector?
.
Check the ohms across the connector on the injector. I think it should read about 1.5 ohms. If you get zero (open circuit) then the...
Mar 15, 2024
Flyer58
reacted to
BCNYOU's post
in the thread
In need of lift and tire advice
with
Like
.
Ya, I just put 33x12.5 on mine because it had a 4 inch lift and it would cost more to remove the spring lift then just try it with 33's...
Mar 13, 2024
Flyer58
replied to the thread
If your transmission skid plate bolts break, then what?
.
I forgot about that. That's what I was originally going to do but when I got the pan removed I found I didn't have enough steel to...
Mar 13, 2024
Flyer58
reacted to
dieselearl's post
in the thread
If your transmission skid plate bolts break, then what?
with
Like
.
drill out and put in nut sets/very easy
Mar 13, 2024
Flyer58
replied to the thread
In need of lift and tire advice
.
The previous owner put 31x10.5 on my 2.5 with stock gears and I can do 70 mph (actual) on a flat highway all day long.
Mar 13, 2024
Flyer58
replied to the thread
If your transmission skid plate bolts break, then what?
.
How does the bottom of the frame look around each bolt hole? Mine was rusted and thin from the inside around each bolt. The sides and...
Mar 12, 2024
Flyer58
reacted to
marcb's post
in the thread
1993 Center Console Replacement
with
Like
.
I added an ammo cam. Self tapping screws, after checking underneath that I would not hit anything.
Mar 12, 2024
Flyer58
reacted to
BCNYOU's post
in the thread
Here it is!
with
Like
.
Wow, beautiful jeep! I also have the automatic in mine too and towed it home with a dolly but I took the rear drive shaft off so...
Mar 11, 2024
Flyer58
reacted to
dodgerammit's post
in the thread
Help with windshield frame hinges
with
Like
.
The speaker magnets were pains for me as well. I unbolted my dash and shifted it around during the procedure since i was restoring the...
Mar 10, 2024
Flyer58
reacted to
jpjeep26uk's post
in the thread
Single Point Injection Wiring
with
Like
.
ECU has been refurbed and seems to be working fine- better than before anyway! I've narrowed down my issue to the single point injector...
Mar 10, 2024
Flyer58
replied to the thread
Recommendations for Setting Up Gears in the Houston Area.
.
A friend used Mckay's Automotive on Budde Rd, The Woodlands. Ask for Alan.
Mar 10, 2024
Flyer58
reacted to
jpjeep26uk's post
in the thread
Non starting after new thermostat and heater core flush
with
Like
.
Hi all, bit of an update to my no spark issue. I eventually sent the ECM off to a local PCB / ECM repair place who refurbed it. Not...
Mar 10, 2024
Top
Bottom