Forums
New posts
Search forums
Image search
Shop
Amazon Store
T-Shirts
Stickers
Members
Current visitors
Supporting Member Upgrade
Sponsors
About
Log in
Register
Search
Search titles only
By:
Search titles only
By:
New posts
Search forums
Image search
Search
Search titles only
By:
Search titles only
By:
Menu
Install the app
Install
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Forums
Jeep Wrangler YJ
YJ General Discussion
TPS setting
Reply to thread
Message
<blockquote data-quote="deadpool1" data-source="post: 439698" data-attributes="member: 21229"><p>the O2 sensor can be removed (unplugged) to test drive the car. </p><p>to see if it runs better.(unplugged the volts go to steady 0-.45vdc. )</p><p>the 02 will read wrong if there are exhaust pipe cracks anywhere near the 02 sensor.</p><p>causes the 02 to slam to 0vdc output and EFI goes full rich, even fouling spark plug tips black.(seen)</p><p>do short drives,</p><p>if running too rich the CAT can even melt.</p><p>so test for short drives. only. </p><p>the 02 sensor , this year , only tests , with a scope work,</p><p>here is OBD2 doing, a simulated 02 scan plot, the O2 output swings fast. (real data on real car) not this car. on 1996+ up.</p><p>that swing is the PCM trimming fuel on the fly, fast. 6 times second possible</p><p>it swings so fast this cheap tool can not see all the swings, but we know it did</p><p>you can not do this with OBD1, nobody sells a RENIX tool.</p><p>this 02 can show bad all these ways</p><p>below is good photo.</p><p>it can be dead the O2 output pin.</p><p>stuck high</p><p>stuck low</p><p>or shifted high or low failed.</p><p>with 02 working mPG goes to max. << this is why we want it so.</p><p></p><p></p><p></p><p>[ATTACH=full]121932[/ATTACH]</p></blockquote><p></p>
[QUOTE="deadpool1, post: 439698, member: 21229"] the O2 sensor can be removed (unplugged) to test drive the car. to see if it runs better.(unplugged the volts go to steady 0-.45vdc. ) the 02 will read wrong if there are exhaust pipe cracks anywhere near the 02 sensor. causes the 02 to slam to 0vdc output and EFI goes full rich, even fouling spark plug tips black.(seen) do short drives, if running too rich the CAT can even melt. so test for short drives. only. the 02 sensor , this year , only tests , with a scope work, here is OBD2 doing, a simulated 02 scan plot, the O2 output swings fast. (real data on real car) not this car. on 1996+ up. that swing is the PCM trimming fuel on the fly, fast. 6 times second possible it swings so fast this cheap tool can not see all the swings, but we know it did you can not do this with OBD1, nobody sells a RENIX tool. this 02 can show bad all these ways below is good photo. it can be dead the O2 output pin. stuck high stuck low or shifted high or low failed. with 02 working mPG goes to max. << this is why we want it so. [ATTACH type="full"]121932[/ATTACH] [/QUOTE]
Verification
Post reply
Forums
Jeep Wrangler YJ
YJ General Discussion
TPS setting
Top
Bottom