Search results

Any way to stop this leak without dropping the oil pan? Gasket is felpro and brand new. Tighten the bolts up? Squirt some RTV over the area?

Hi All, I have a 92 YJ with a ford 8.8 rear axle. I noticed that since I increased my rear pinion (when installing a slip yoke eliminator), the diff cover hits the gas tank skid just a little bit, when going over bumps on the road. Seems to be the thick axle plus the increased pinion creates...

Hi All, I am stuck with this one. I had a heavy duty rugged ridge drag link and tie rod installed. Now, because the tie rod is significantly thicker than stock, at full turn (to the left only) it hits the diff cover. I’ve adjusted the steering stops, but it’s taken a massive amount of...

I have a 92 YJ with the original gearbox. Lifted 4 inches with 12.5x33 tires. 4.10 gear ratio. Suggestions? I’m looking for tighter handling

2 questions 1 - I have a 4 inch lift to my 92 YJ. The kit I used was a rough country lift. I just swapped out the springs for Rubicon Express Springs. Made for a 4 inch lift. Each new spring, front and back, are identical. Am I supposed to have different Rubicon Express springs for the front...

Hi All - I recent installed boomerang shackles that give an extra 1.5 inches of lift. My question is, do I need to change my leaf springs to a larger size due to this, or can I keep them? I allready have springs on there (Rubicon Express) for a 4 inch lift, which is what I have. Should I keep...

Hey everybody… I know this is a big topic on here. I recently swapped out my stock Dana 35 axle for a Ford 8.8 with disc brakes. Prior to the swap and after the swap my brakes were pretty spongy. I was told I should replace the master cylinder. Should I replace the master cylinder with the YJ...

I recently swapped out my rear Dana 35 for a Ford 8.8 axle. Everything went well, but my only issue is that the rear calipers are simply not getting enough brake fluid. I’ve read across the Internet that the stock master cylinder should be sufficient, but I know for a fact that ideally when...

So I am going ahead to do the rear axle swap. Replacing my Dana 35 with a 2001 Ford Explorer rear axle. I’d love to hear any and all feedback before the work starts. One question is that I have a 92 YJ - automatic 3 speed. The Ford axle is from a 5 speed automatic. Does that matter? Any other...

I have. 92 YJ. Lifted 4 inches. Additionally has boomerang shackles. The other day I noticed when looking directly at my car facing its front, the leaf springs both curve towards one side of the car. I see some of the bushings connection the leaf springs to the shackles worn out as well...

Hey everyone - Here to ask a common gearing question to which I have never received a clear answer on … I have a 92 YJ geared at 3.55. Automatic transmission. 3 gears. 4 inch lift. 33x12.5 tires. I live in NY and this is my one and only car. I drive through NYC nearly everyday. A lot of stop...

I have a 92 YJ in pretty good condition. Have put in a lot of work over the years. The frame is not bad, though I can identify some problem areas…IE rust. It’s OK for now but if possible I’d like to strengthen and reinforce these parts of the frame before it gets bad. Any suggestions on how...

I have a 92 YJ in pretty good condition. Have put in a lot of work over the years. The frame is not bad, though I can identify some problem areas…IE rust. It’s OK for now but if possible I’d like to strengthen and reinforce these parts of the frame before it gets bad. Any suggestions on how...

I have a 92 YJ in pretty good condition. Have put in a lot of work over the years. The frame is not bad, though I can identify some problem areas…IE rust. It’s OK for now but if possible I’d like to strengthen and reinforce these parts of the frame before it gets bad. Any suggestions on how...

I have a 92 YJ that I I’d like to get lifted. About 4 inches. Yet it seems that every lift I could possibly find is on backorder. Anyone else notice this? Anyone have any suggestions for ordering a lift kit. I’ve waited over a month and now delayed again...