Latest activity Postings Images About
-
-
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.As far as I'm aware the shaft is floating inside the diff, trimming it will help with the pressure on the bearing? I'm pretty sure the... -
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.UPDATE - I "fixed" the issue. Well, maybe I should say that I override the issue, here's what I did: I talked to the previous owner of...
-
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.SET10, same as you would use for D44 as per what they told me in the store
-
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.I got D60 and I’m pretty confident that the TIMKEN kit I got fits the axle since I got it from a local store that specialises in Jeep...
-
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.Update - I installed a brand new TIMKEN kit on the problematic axle and the same issue still exists…. I’m starting to think that I need...
-
-
Sufa1992 reacted to machoheadgames's post in the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal with
Like.
Didn’t realize you’re overseas - that makes more sense now. I don’t think you have a D60, I think you have the factory export D44. But... -
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.So today I tried to press the bearing further, plus checked it's race to make sure it's seated all the way in and it does. No change...
-
Sufa1992 reacted to machoheadgames's post in the thread 1994 Hunter Green SE “Back to Stock” Thread with Like.
Hey all, some of you may have seen my other build thread. I think I’m going to stop using that one. Over the years there’s just been too...
-
Sufa1992 reacted to machoheadgames's post in the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal with Like.
It's possible. I used to have a TJ D44 in my YJ and I installed both SKF and Timken in it. Neither of them seemed to give me any install...
-
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.I’ll share the VIN later when I’m near it, it’s not my daily driver so I’m parking it away… In the meantime, I took a short drive today...
-
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.Of course, thx a lot.
-
-
Sufa1992 reacted to machoheadgames's post in the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal with Like.
Someone swapped your rear axle from one that was originally installed in a 1987-1989 YJ. I wonder if the new bearing is improper...
-
Sufa1992 reacted to Flyer58's post in the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal with Like.
Those axles are different than the ones in my '92 YJ. My axles are held in place with C-clips on the differential end, not the four...
-
Sufa1992 replied to the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal.To be honest the nuts fitted just fine, torqued them all to around 47 ft\lb and didn’t notice anything strange. After driving for a...
-
-
Sufa1992 posted the thread 92 YJ stiff rear axle after replacing bearing, locking ring and seal in YJ General Discussion.Hello Everyone, new here! I was replacing my outer rear axle seal, bearing and locking ring yesterday and when I tightened the 4 nuts...
-
-
-
Loading…
-
Loading…
-
Loading…
