Forums
New posts
Search forums
Image search
Shop
Amazon Store
T-Shirts
Stickers
Members
Current visitors
Supporting Member Upgrade
Sponsors
About
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Current visitors
Supporting Member Upgrade
Search
Search titles only
By:
Search titles only
By:
Menu
Install the app
Install
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Flyer58's latest activity
Flyer58
replied to the thread
Clutch or Master Cylinder/Slave?
.
I missed that part about the redline fluid. IF you transmission is level it should take about 3.3 quarts. There's a bolt hole the...
Mar 24, 2024
Flyer58
replied to the thread
Clutch or Master Cylinder/Slave?
.
Also check the transmission fluid level. It may be low or never changed at all. The synchros are made of a sacrificial metal that...
Mar 24, 2024
Flyer58
replied to the thread
Clutch or Master Cylinder/Slave?
.
Mar 23, 2024
Flyer58
replied to the thread
Clutch or Master Cylinder/Slave?
.
Reverse always crunches since there's no synchro for it. I always go into 2nd to stop any rotation then quickly into reverse. That...
Mar 23, 2024
Flyer58
replied to the thread
Thinking about a YJ
.
I wouldn't drive it with that rust. Patch kits are available, do you have a welder? If you're paying someone else for all the repairs...
Mar 23, 2024
Flyer58
reacted to
White J's post
in the thread
EAG Military Star 2 Tubular Door
with
Like
.
I don't have any.
Mar 22, 2024
Flyer58
replied to the thread
EAG Military Star 2 Tubular Door
.
I'm guessing you'll need to unplug the interior courtesy light so it doesn't stay on all the time?
Mar 21, 2024
Flyer58
replied to the thread
Fuse box questions
.
Those are female spade connectors. You can find almost all answers in the factory service manuals find in the resources section in this...
Mar 20, 2024
Flyer58
replied to the thread
Need Help Reinstalling Rear Driveshaft
.
When removing the U-joint did any of the cups fall off and possibly lose some of the roller needle bearings? It's also easy for then to...
Mar 18, 2024
Flyer58
reacted to
dodgerammit's post
in the thread
Help with windshield frame hinges
with
Like
.
I had a similar issue on a repop half door I purchased. The door sat WAY too far forward. Like, rubbing the tub at the hinges forward...
Mar 17, 2024
Flyer58
reacted to
machoheadgames's post
in the thread
1994 Hunter Green SE “Back to Stock” Thread
with
Like
.
Been busy lately. Finally cleaned up the garage, which helps a lot. Through parts of December and January and a bit of February, I got...
Mar 16, 2024
Flyer58
replied to the thread
Is there anything wrong with this fuel injector?
.
Check the ohms across the connector on the injector. I think it should read about 1.5 ohms. If you get zero (open circuit) then the...
Mar 15, 2024
Flyer58
reacted to
BCNYOU's post
in the thread
In need of lift and tire advice
with
Like
.
Ya, I just put 33x12.5 on mine because it had a 4 inch lift and it would cost more to remove the spring lift then just try it with 33's...
Mar 13, 2024
Flyer58
replied to the thread
If your transmission skid plate bolts break, then what?
.
I forgot about that. That's what I was originally going to do but when I got the pan removed I found I didn't have enough steel to...
Mar 13, 2024
Flyer58
reacted to
dieselearl's post
in the thread
If your transmission skid plate bolts break, then what?
with
Like
.
drill out and put in nut sets/very easy
Mar 13, 2024
Top
Bottom